• Flex Reg

We have re-designed our Flex Reg Regulator. Moving the Power Switch to the end of the unit and raising the Secondary Voltage output from 5v to 5.3v.  We have also changed the adjustable output to start at 4.8v instead of 5.2v.  Installation is simple... Connect your 2s Lipo/Li-Ion Battery, connect the 2 x 6" Male to Male Servo Connectors into the Rx (Rudder and Gyro Gain Suggested), then connect those specific plugs onto the unit for for Regulated 5.3v.

Closely similar to our 6v Voltage Regulator, our new Adjustable Voltage Regulator is going to be a top runner for Voltage Regulator needs. This unit will allow upwards of 11.1v input from an array of battery technologies, (Ni-Cd, Ni-Mh, Li-Ion and Li-Po). Output Voltage is user adjustable within a range based on the input voltage supplied to the unit. With a 7.4v input, the Voltage range can be set anywhere from 4.8v - 6.5v and with an 11.1v input, you can go upwards of over 8.5v.* The best way to set the Voltage Output is through an already connected Electronic Device (ie... GV-1) that displays Voltage. Otherwise any Volt Meter would work fine.

The onboard switch is designed not to fail during flight. If a short or overload occurs while the Regulator is in the on position, the Regulator will remain in the on position.

Also built into the same unit is a 5.3v Regulator for use with Gyro / Tail Servos that are suggested to use an input of 4.8v - 5.3v. This compact and light-weight Voltage Regulator will definatley exceed your expectations!!!

The Unique design of the Heatsink with ULTRA-THIN Fins allows for super fast dissipation of heat and makes Installation a breeze due to not needing air-flow over the Heatsink.

Unit comes packaged with 2 x 6" Male to Male, 22AWG Servo Extensions.

 


 

Min. Input Voltage: 7.4v
Suggested Input Voltage: 7.4v - 11.1v*
Main Output Voltage w/ 7.4v: Adjustable 4.8v - 6.5v @ 10A
Main Output Voltage w/ 11.1v: Adjustable 4.8v - 8.5v+ @ 10A
Gyro/Tail Output Voltage: Constant 5v @ 1.5A
Max. Main Amp Rating: 16A
Max. Gyro/Tail Amp Rating: 3A
Heatsink Material: Aluminum
Length of Lead Plugs: 6" Each
Plug Type: Universal
Size: 60mm x 30mm x 9mm
Weight: 33.5g
Download Manual  

 

* for nominal performance, use a 7.4v input voltage

* We suggest that if you are going to be running the output voltage under 7v to use a 7.4v Input. Only if you are going to be running the output at over 7v to use an 11.1v.

Write a review

Please login or register to review

Flex Reg

  • $60.00


Related Products

Igniter

Igniter

We have completely r..

$45.00

Deans Compatible Connectors

Deans Compatible Connectors

Available in packs o..

$4.00

Expandable Braided Servo Wrap

Expandable Braided Servo Wrap

Protect your Servo a..

$5.00

Featured

Lipo Discharger Pro Audible Alert Accessory

Lipo Discharger Pro Audible Alert Accessory

This is our NEW Lipo..

$15.00

Safe Switch Duo Pro V2

Safe Switch Duo Pro V2

This is the NEW Safe..

$75.00

Safe Switch 2 Plus

Safe Switch 2 Plus

The new Safe Switch ..

$40.00

Universal Lipo Discharger Pro V2

Universal Lipo Discharger Pro V2

This is our NEW Univ..

$115.00